AVR210 harman/kardon
Remote Control Functions
IMPORTANT NOTE: The AVR 210Os remotef AVR Selector: Pressing this button willselect the channel being adjusted, then press the
may be programmed to control up to eightswitch the remote so that it will operate theSet button o, followed by the �/U buttons
devices, including the AVR 210. Before using theAVR 210Os functions. If the AVR 210 is in themq again, to change the level setting. (See
remote, it is important to remember to press theStandby mode, it will also turn the AVR 210 on.page 29 for more information.)
Input Selector button e that corresponds to
the unit you wish to operate. In addition, theg AM/FM Tuner Select: Press this button tom� Button: This multipurpose button is
AVR 210Os remote is shipped from the factory toselect the AVR 210Os tuner as the listeningused to change or scroll through items in the on
operate the AVR 210 and most Harman Kardonchoice. Pressing this button when the tuner isscreen menus, or to change configuration set-
CD or DVD players and cassette decks. Thealready in use will select between the AM andtings such as output levels.When changing an
remote is also capable of operating a wide vari-FM bands.item such as the surround mode or digital input
ety of other products using the control codesdirectly, first press the function or mode to be
h Test Button: Press this button to beginchanged (e.g. press the Surround Mode button
that are part of the remote. Before using the
the sequence used to calibrate the AVR 210Os
remote with other products, follow the instruc-j to select a surround mode or the Digital
output levels. (See page 21 for more information
tions on pages 33�36 to program the properbutton p to change the digital input) and then
on calibrating the AVR 210.)press this button to scroll down through the list
codes for the products in your system.
of available choices.
i Sleep Button: Press this button to place
It is also important to remember that many of
the unit in the Sleep mode. After the timen� Button: This button is used to change
the buttons on the remote take on different
shown in the display, the AVR 210 will auto-
functions, depending on the product selectedthe menu selection or setting during some of
matically go into the Standby mode. Each press
using the Device Control Selectors. The descrip-the setup procedures for the AVR 210.
of the button changes the time until turn-off in
tions shown here primarily detail the functions
the following order:o Set Button: This button is used to enter
of the remote when it is used to operate the
9080706050settings into the AVR 210Os memory. It is also
AVR 210. (See page 34 for information about
minminminminmin
used in the setup procedures for delay time,
alternate functions for the remoteOs buttons.)
40302010OFFspeaker configuration and channel output level
minminminmin
adjustment.
a Power On Button: Press this button to
turn on the power to a device selected by press-Note that this button is also used to change
p Digital Select: Press this button to assign
ing one of the Input Selectors e.channels on your TV when the TV is selected.
one of the digital inputs hi$ to a source.
b IR Transmitter Window: Point this win-(See page 26 for more information on using
When the AVR 210 remote is being programmed
digital inputs.)
dow towards the AVR 210 when pressing buttons
with the codes to operate another device, this
on the remote to make certain that infrared com-
button is also used in the OAuto Search� process.qU Button: This multi-purpose button is
mands are properly received.
(See page 33 for more information on program-used to change or scroll through items in the on
ming the remote.)
c Program/SPL Indicator: This three-colorscreen menus, or to change configuration set-
indicator is used to guide you through thetings such as output levels.When changing an
jSurround Mode Selector: Press thisitem such as the surround mode or digital input
process of programming the remote or learning
button to begin the process of changing
commands from a remote into the AVR 210Osdirectly, first press the function or mode to be
the surround mode. After the button has
remote code memory and it is also used as achanged (e.g. press the Surround Mode button
been pressed, use the �/U buttons mqj to select a surround mode or the Digital
level indicator when using the remoteOs EzSet
to select the desired surround mode. (See pagebutton p to change the digital input) and then
capabilities. (See page 21 for more information
25 for more information.) Note that this button
on setting output levels, and see page 33 forpress this button to scroll down through the list
is also used to tune channels when the TV is
information on programming the remote.)of available choices.
selected using the device Input Selector
d Power Off Button: Press this button toe. When the AVR 210 remote is being pro-r Numeric Keys: These buttons serve as a
ten-button numeric keypad to enter tuner preset
place the AVR 210 or a selected device in thegrammed with the codes of another device, this
Standby mode.button is also used in the OAuto Search�positions. They are also used to select channel
process. (See page 33 for more information onnumbers when TV has been selected on the
e Input Selectors: Pressing one of theseprogramming the remote.)remote, or to select track numbers on a CD,
buttons will perform three actions at the sameDVD or LD player, depending on how the
time. First, if the AVR 210 is not turned on, thisk Night Mode: Press this button to activateremote has been programmed.
will power up the unit. Next, it will select thethe Night mode. This mode is available in spe-
source shown on the button as the input to thecially encoded digital sources, and it preservess Tuner Mode: Press this button when the
AVR 210. Finally, it will change the remote con-dialog (center channel) intelligibility at low tuner is in use to select between automatic
tuning and manual tuning. When the button is
trol so that it controls the device selected. Aftervolume levels.
pressing one of these buttons you must presspressed so that the AUTO indicator W goes
l Channel Select Button: This button is
the AVR Selector button f again to oper-out, pressing the Tuning buttons u8 will
used to start the process of setting the AVR 210Osmove the frequency up or down in single-step
ate the AVR 210Os functions with the remote.
output levels to an external source. Once this but-increments. When the FM band is in use, press-
ton is pressed, use the �/U buttons mq toing this button when a stationOs signal is weak
12 REMOTE CONTROL FUNCTIONS |